Building the Eclipson Gö 1 Wolf — 3D-Printed Vintage Glider

Notes on building Eclipson's 3D-printable Göppingen Gö 1 Wolf — a free vintage glider model — including the filament I used and the printing guide reference.

About the Model

The Gö 1 Wolf is a 1935 German training glider, available as a free 3D-printable RC model from Eclipson Airplanes:

Gö 1 Wolf — Eclipson Airplanes (free download)

I printed this one for a friend.

Filament

The recipe Eclipson recommends — and what I used:

Tip: LW-PLA must be dry — bake or dehydrate it before printing or you'll get poor foaming and weak parts.

Printing Guide

Eclipson's official printing details PDF (settings, foaming temperatures, infill, walls):

Gö 1 Wolf — Printing Details (PDF)

Build Photos

Gö 1 Wolf — printed parts
Gö 1 Wolf — assembly detail

Comments

Post a Comment

Popular posts from this blog

INAV OSD over DJI Goggles V2 + Caddx Vista (WTFOS Setup)

Image
How to get the full INAV OSD overlay (battery, GPS, artificial horizon, warnings) on the original DJI HD FPV Goggles V2 with a Caddx Vista air unit, by rooting both devices with WTFOS. Scope & status: WTFOS works for the original DJI HD FPV Goggles V2 + DJI/Caddx Vista Air Unit (the older 2.4 GHz / 5.8 GHz HD system). It does not apply to the newer DJI O3 / O4 Air Units or to Goggles 2 / Goggles 3 / Goggles N3 — those have a native MSP DisplayPort path. The WTFOS project is community-driven ( fpv.wtf , currently v2.3.0) and you root your own gear at your own risk. What You're Doing Rooting the goggles + Vista with the margerine exploit. Installing WTFOS (a community OS-on-top) on both. Telling INAV to send its native OSD via MSP to the air unit, which WTFOS overlays on the analog video feed. Reference Build Video Walkthrough of the result: INAV OSD over DJI HD (YouTube) Steps Wire MSP to the Vista. Check your flight-controller manufa...
Read more

Building the Dart Mini 2 F3K Discus-Launch Glider

Image
Build log of a Dart Mini 2 — a small F3K discus-launch glider (DLG) from RCGlider.eu — assembled for a friend over about two weeks. Photos cover the whole process from carbon parts to maiden-ready airframe. About the Model The Dart Mini 2 is RCGlider.eu's compact F3K-class hand-launch glider. It's a moulded composite kit aimed at light-wind throwing and learning DLG technique without committing to a full 1.5 m F3K. The Build Took roughly two weeks of evenings. The kit comes well-prepped — most of the time is on: Servo install and linkages (4 micro servos: rudder, elevator, two wing surfaces). Pushrod routing through the boom. Receiver and battery placement for correct CG. Surface throws and exponential set up on the radio. Maiden Video Build Photos (36 images)
Read more

EdgeTX on the RadioMaster TX16S — Servo Geometry & Travel Tips

Image
Quick reference for EdgeTX (and OpenTX) users on the RadioMaster TX16S: getting control-link geometry right at the servo arm and slowing down servo travel for scale or smooth control. Control Link Geometry The angle between the servo arm and the control rod has a huge effect on how linear (and how strong) the surface response is. Get it wrong and you end up with binding, lost throw, or unwanted differential. This short demo walks through the geometry visually: Control link geometry demo (YouTube) Slowing Down Servo Travel For scale models, retracts, flaps or just smoother flying, you can apply a delay or a slow rate to a servo channel directly in OpenTX/EdgeTX — no extra hardware needed. Step-by-step using mixer "Delay" and "Slow": OpenTX/EdgeTX — How to Delay and Slow Servo Travel (YouTube) Where to Configure Delay (s) — wait N seconds before the servo starts moving after a switch change. Slow Up / Slow Down (s) — limit how fast the servo can...
Read more